Optical Smoke Det Activ En54-7 Wiring Diagram - Optical Smoke Det Activ En54 7 Wiring Diagram Z630 3p Datasheet Manualzz 5 En54 Listed Compatible Control Panel Eol Last Detector Base Resistor Led Detector Head Opening Here 6 1 3 - 1 shows the circuit of the smoke detector, while fig.
Optical Smoke Det Activ En54-7 Wiring Diagram - Optical Smoke Det Activ En54 7 Wiring Diagram Z630 3p Datasheet Manualzz 5 En54 Listed Compatible Control Panel Eol Last Detector Base Resistor Led Detector Head Opening Here 6 1 3 - 1 shows the circuit of the smoke detector, while fig.. Connect the detector base to the intruder alarm panel using the wiring diagram. Carries the prestigious 'certalarm' system 5 mark Led continuously emitting red light remote output: Choose the proper place for installation of the fire detector. Photoelectric smoke detector also has the provision of connecting a remote led indicator.
Normal detection area is 25 square metres. Note:do not install the detector near sources of steam, condensation or smoke, 1 shows the circuit of the smoke detector, while fig. 5 en54 listed compatible control panel eol last detector base resistor led detector head opening here 6 1 3 4 6 1 3 4 remote indicator base class a optional wiring note: Install the sensor into the sensor base.
The c4416 optical smoke detector uses an infrared light source and a photodiode to detect smoke.
Firex duct mounted smoke detector universal ionization. Disconnect the main power supply before installing the detector! Its strong repeater functionality expands. Earth terminal is provided to maintain earth screen continuity. Typically used in escape routes, living areas, bedrooms & other enclosed spaces. Note:do not install the detector near sources of steam, condensation or smoke, Red led illuminates when the detector is in alarm. Led continuously emitting red light remote output: A hardwired smoke alarm installation involves wiring one of the smoke detectors (closest to the voltage source) to a 120 vac breaker in the main electric panel or tapping from a 120 v electrical box, wiring it using a 14/2 cable with a black (live), a white (neutral), and a ground wire, as shown by the diagram in figure 5. The c4416 optical smoke detector uses an infrared light source and a photodiode to detect smoke. When smoke is detected, the relay energises to activate the audio/visual warning alarm. 5 en54 listed compatible control panel eol last detector base resistor led detector head opening here 6 1 3 4 6 1 3 4 remote indicator base class a optional wiring note: 5.4 the wiring diagram for detectors.
Insert the detector into the base and rotate clockwise until it drops into place. Earth terminal is provided to maintain earth screen continuity. The en 54 fire detection and fire alarm systems is a series of. The c4416 optical smoke detector uses an infrared light source and a photodiode to detect smoke. Optical detectors are typically used in escape routes, living areas, bedrooms and enclosed spaces to give an early indication of fire.
Less than 1 second alarm indicator:
Less than 1 volt reset time: Carries the prestigious 'certalarm' system 5 mark When smoke enters the optical chamber across the path of the infrared beam, light is scattered by particles of smoke in all directions, some of which falls on the. Planning, design en 54 fire detection and. Led continuously emitting red light remote output: Note:do not install the detector near sources of steam, condensation or smoke, Choose the proper place for installation of the fire detector. The c4416 optical smoke detector uses an infrared light source and a photodiode to detect smoke. In the absence of smoke, light passes in front of the photodiode in a straight line. On the rear of all photain heat detector data sheets, a diagram showing the relevant coverage they provide is shown. Typically used in escape routes, living areas, bedrooms & other enclosed spaces. Polarity must be observed on detector as indicated on schematic wiring diagram. Connect the detector base to the fire panel using the wiring diagram.
The detector's design widely applies to all kinds of industrial and commercial constructions with its high resistance to humidity, wide operating temperature range, high reliability and ease of installation and configuration. Wire the sensor base per the wiring diagram, figure 1. The en 54 fire detection and fire alarm systems is a series of. Red led illuminates when the detector is in alarm. Works using the light scatter principle.
Typical quiescent and alarm currents detector status 12 schematic wiring diagram of series 60 monitored detector.
A hardwired smoke alarm installation involves wiring one of the smoke detectors (closest to the voltage source) to a 120 vac breaker in the main electric panel or tapping from a 120 v electrical box, wiring it using a 14/2 cable with a black (live), a white (neutral), and a ground wire, as shown by the diagram in figure 5. Red led illuminates when the detector is in alarm. Photoelectric smoke detector also has the provision of connecting a remote led indicator. Connect the detector base to the intruder alarm panel using the wiring diagram. The en 54 fire detection and fire alarm systems is a series of. 1 shows the circuit of the smoke detector, while fig. Choose the proper place for installation of the fire detector. 4.2.2 the optical smoke detection shall be designed in accordance with the functional requirements of en 54 part 7. Works using the light scatter principle. 5 en54 listed compatible control panel eol last detector base resistor led detector head opening here 6 1 3 4 6 1 3 4 remote indicator base class a optional wiring note: Typically used in escape routes, living areas, bedrooms & other enclosed spaces. Fire alarm system/smoke detector wiring diagramconventional wiring diagram. Wire the sensor base per the wiring diagram, figure 1.
Komentar
Posting Komentar